![]() View objects that are high in the sky if possible.Using your telescope out a window is NEVER recommended.You’d be surprised how much more you’ll see from your local lake or park when compared to a backyard in the city. This will allow you to see much fainter objects. If possible, view from a location that has relatively few lights.This will provide a more stable foundation for viewing, especially if you’ve drawn a crowd with your new telescope. For best results and fewer vibrations set your telescope up on a level location on the ground rather than your concrete driveway or your wooden deck. Your telescope is a very sensitive instrument.Low power is recommended for most viewing conditions. NOTE: Magnification is calculated magnification. To calculate magnification, use the following formula, in which FL = focal length:ĮYE LENS CHART & THEORETICAL POWER LIMITS The magnification (or power) of a telescope varies depending upon the focal length of the eyepieceīeing used and the focal length of the telescope.Ģ. To achieve a truly sharp focus, never look through glass windows or across objects that produce heat waves, such as asphalt parking lots.ġ. For more distant objects, turn the focus knob in the opposite direction.ģ. To focus on an object that is nearer than your current target, turn the focusing knob toward the eyepiece (i.e., so that the focus tube moves away from the front of the telescope). Once you have found an object in the telescope, turn the focus knob until the image is sharp.Ģ. Once it’s in the field of view, tighten the altitude and azimuth locks.ġ. Look through the finderscope and pan the telescope until the object appears in the field of view. This will extend the life of both the battery and the LED.ġ. Remember to always turn the power off after you have found an object. This will make it easier to get an accurate alignment. Turn the variable brightness control counterclockwise, until the red dot is the same brightness as the alignment star. If the LED dot is brighter than the alignment star, it may make it difficult to see the star. Without moving the main telescope, turn the StarPointer’s azimuth and altitude alignment controls until the red dot is directly over the alignment star. The red dot is relative to the bright star. ![]() If the StarPointer is not aligned, take notice of where If the StarPointer is perfectly aligned, you will see the red LED dot Locate a bright star or planet and center it in a low power eyepiece in the main telescope. To turn on the StarPointer, rotate the variable brightness control clockwise until you hear a “click.” To increase the brightness level of the red dot, continue rotating the control knob about 180° until it stops.ģ. Like all finderscopes, the StarPointer must be properly aligned with the main telescope before it can be used.Ģ. The star pointer is a zero magnification pointing tool that uses a coated glass window to superimpose the image of a small red dot into the night sky. It’s like having a laser pointer that you can shine directly into the night sky. The StarPointer is the quickest and easiest way to point your telescope exactly at a desired object in the sky. Do not view the sun with this telescope or even with the naked eye.ġ. Insert eyepiece into open end of Barlow and secure.ĬAUTION! Viewing the sun can cause permanent eye damage. TousetheBarlow,insertBarlow(Fig.5)intothefocustube.Securebytightening small retaining screw. The telescope is now fully assembled and ready for use.ħ. Reflectors (mirrors) are used mainly for astronomical purposes. Only refractor telescopes come with erector eyepieces. We recommend the use of the low magnification eyepiece when the telescope is used for terrestrial viewing. To use the telescope for terrestrial view and to correct the mirrored image, remove the diagonal and replace with the erecting eyepiece (fig 5). With the use of the diagonal the image appears erect but with a left to right inversion (mirror like). NOTE ( Refractor Models only): In all astronomical telescopes, the image appears upside down. ( Reflector models) Insert eyepiece into focusing tube and tighten set screw to begin viewing. ( Refractor models) Put an eyepiece (H25mm) into the diagonal, then attach the diagonal to the telescope, tightening the retaining screws (Fig. Position the finderscope bracket on the telescope main body (Fig. Remove the finderscope (G) with finderscope bracket (F) attached from the box. Attach telescope main body (H) by aligning the hole in the telescope saddle with that in the yoke.ĥ. Attach the accessory tray (P) to the center leg braces on the tripod legs (Fig 2) and insert accessory tray and bolt through center of tray into braces and tighten bolt.Ĥ. Extend the tripod legs to the desired height (at equal lengths) and tighten the clamps on each leg to hold it in position (Fig. Your telescope has adjustable (telescoping) legs (Fig.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |